2000+ California CDL Test Q&A 2023 [FREE ACCESS]

In this session, you will be able to find 2000+ California CDL Test Questions and Answers which will help you for the upcoming exams.

Please note that all answers will be revealed for free. So let’s get started right away!

California CDL Test Questions and Answers – 2000+ Q&A Solved

All California CDL Test Questions and Answers to different topics below are checked twice before publishing them to you.

You can select any topic of your wish and get the answers for FREE:

California CDL Test Questions and Answers

 

California CDL Test Questions and Answers – General Knowledge

Below you can find questions and their respective answers for the topic “General Knowledge”:

=> Find California CDL GK Test Questions and Answers Here

 

California CDL Test Questions and Answers – Doubles/Triples

Below you can find questions and their respective answers for the topic “Doubles/Triples”:

 

California CDL Test Questions and Answers – Tanker

Below you can find questions and their respective answers for the topic “Tanker”:

Q. An emergency forces you to stop your tanker quickly or crash. You should
Ans: use controlled or stab braking

Q. A smooth bore tank is also known as:
Ans: an un-baffled liquid tanker

Q. Side-to-side surges can cause
Ans: a rollover

Q. Hauling liquids in tankers requires special care for the following reasons
Ans:
– Flat
– Low
– Wide
– High

Q. How does liquid surge affect the handling of a tanker?
Ans: surge can move the truck in the direction the liquid waves move

Q. A baffled tanker is one with
Ans: bulkheads in them with holes that let the liquid flow through

Q. Outage means
Ans: allowance for expansion of liquid

Q. liquid-tight separators between compartments inside tanks are called
Ans: bulkheads

Q. You are driving a tanker truck. The front wheels begin to skid. Which of these is most likely to occur?
Ans: you will continue in a straight line and keep moving forward no matter how you steer

Q. You should know the outage needed for the liquids you carry because
Ans: some liquids expand more than others when they get warm

Q. The movement of the liquid in partially filled tanks is called
Ans: surging

Q. Which of these statements about tankers and their center of gravity is true?
Ans:
-Tankers can turn over at the speed limits posted for curves
-Much of the load’s weight is carried high up off the road

Q. A tank endorsement is required for certain vehicles that transport
Ans: liquids and gases

Q. Which of these statements about stopping and speed is true?
Ans: wet roads can double the stopping distance at any speed

Q. The liquid in a tank with baffles can still have what kind of surge?
Ans: side-to-side

Q. The best way to take a curve in a tanker is to slow to a safe speed before entering the curve and then _ as you go through it.
Ans: speed up slightly

Q. Separators with openings or holes in them, that are between compartments in a tank are called
Ans: baffles

Q. The amount of liquid to load into a tank depends on what?
Ans:
– The amount of the liquid will expand
– The weight of the liquid
– Legal weight limits

Q. When your cargo tank has baffles, what handling effect do you expect?
Ans: there will be less front-to-back surge than in a tank without baffles

Q. When you load the small tanks of a cargo tank equipped with bulkheads, you should check the
Ans: distribution of weight

Q. You are driving on a clear night. You must dim your headlights from high to low. You should adjust your speed so you can stop within
Ans: The distance you can see ahead

Q. Empty trucks
Ans: may require a longer stopping distance than full trucks

Q. If you lose your brakes driving a tanker, when should you use an escape ramp?
Ans: Always

Q. Why should you know the outage needed for the liquids you carry?
Ans: Some liquids expand more than others when they get warm

Q. What should you do if you are driving a tank vehicle and need to stop quickly to avoid a crash?
Ans: Use controlled or stab braking

Q. Which of the following can cause a vehicle to skid?
Ans:
– Over braking
– Over steering
– Over acceleration
– Driving too fast

Q. Which of the following is important to remember when pulling a liquid or dry bulk tanker?
Ans:
– Curves, exit, and entrance ramps post speed limits that are safe for cars but may not be safe for tankers
– Most tankers have a high center of gravity
– Tankers can roll over at the speed limits posted for cars

Q. Which of the following is a good rule to follow when using a fire extinguisher?
Ans: Aim at the base of the fire and stay upwind of the fire

Q. Which of the following about emergency steering and tankers is True?
Ans: Do not apply the brakes when making a quick steering movement

Q. Which fire can you use water to put out?
Ans: Tire

Q. When you unload the smaller tanks of a tank with bulkheads, be careful to check your:
Ans: Weight distribution

Q. Which of these should you remember in an emergency?
Ans: Heavy vehicles can turn more quickly than they can stop

Q. You should be very cautious when driving smooth bore tanks. This is especially true when you are:
Ans: Starting or stopping

Q. A “smooth bore tank” will
Ans: Have more surge than a baffle tank

Q. A smooth bore tank that is loaded to 50% capacity will:
Ans: Have more surge

Q. What should you do if you are driving a loaded tanker and you are exiting the highway using an offramp that curves downhill?
Ans: Slow to a safe speed before the turn

Q. A liquid tank with baffles can still have what kind of surge?
Ans: Side to Side

Q. Which of these is likely to occur if you are driving a tanker and the front wheels begin to skid?
Ans: You will keep moving forward in a straight line no matter how much you steer

Q. Which of the following must you consider when loading a cargo tank with liquid?
Ans:
– The weight of the fluid
– The amount that the liquid will expand during transit
– The weight limits in the states in which you will be driving

Q. How will a truck with a baffled cargo handle be on the road?
Ans: There will be less front-to-back surge than tanker with baffles

Q. Normal surge is:
Ans: Front to back and side to side

Q. It is best to keep the center of gravity:
Ans: Low

Q. What difference in handling can you expect in a tank with bulkheads?
Ans: Less front-to-front surge than with smooth bore tanks

Q. What will liquid surge do to the handling of a tank vehicle?
Ans: Can move the vehicle in the same direction the liquid moves

Q. Why is it important to know the outage needed for the liquids?
Ans: Some liquids expand more when they get warm

Q. What is liquid surge caused by?
Ans: Movement of the liquid in the tank

Q. Too much weight on the steering axle can cause hard steering.
Ans: True

Q. Baffles divide a tank into several smaller tanks.
Ans: False

Q. Starting and stopping with a smooth bore tank requires extra caution.
Ans: True

Q. It is not important to know the outage of bulk liquids.
Ans: False

Q. A bridge formula permits less maximum axle weight for axles that are closer together.
Ans: True

Q. Dry bulk tank loads tend to have a high unstable center of gravity.
Ans: True

Q. Too much weight on the driving axle is likely to cause poor traction.
Ans: False

Q. The driver is only responsible for an overloaded vehicle if he loaded it himself.
Ans: False

Q. Forward and backward surge is especially high in tanks that are not baffled.
Ans: True

Q. Dense liquids are likely to exceed legal weight if the tank is fully loaded.
Ans: True

Q. Tank vehicles are usually top-heavy.
Ans: True

Q. Bulkheads reduce the importance of weight distribution.
Ans: False

Q. Always leave room for expanding liquids when loading a tank.
Ans: True

Q. Sanitation regulations forbid the use of baffled tanks to transport food products.
Ans: True

Q. Baffled tanks control side to side surge.
Ans: False

Q. Surging is less dangerous in poor driving conditions.
Ans: False

Q. Baffled tanks have bulkheads with holes in them.
Ans: True

Q. Liquid surge tends to push the truck in the direction the liquid wave is moving.
Ans: True

Q. Tankers can turn over at the posted speed limits on curves.
Ans: True

Q. Tank vehicles have a high center of gravity.
Ans: True

Q. A tank vehicle is a vehicle used to transport:
Ans: Any liquid or liquefied gaseous material in a permanently attached tank.

Q. Hauling liquids in tanks requires special skills because:
Ans: Of the products, they are designed to haul.

Q. Unbaffled tanks are used for hauling:
Ans: Food products

Q. Smooth bore tankers are more difficult to drive because?
Ans: They have nothing to slow down the flow of the liquid.

Q. Use of baffles is sometimes forbidden because:
Ans: Of sanitation requirements

Q. Tests have shown that tankers will turn over at posted:
Ans:
– Off ramp speed
– On ramp speed
– Speeds on highway curves

Q. Bulkheads are?
Ans: Used to slow down the movement of liquids in transit

Q. Liquid surge is most dangerous in tanks:
Ans: Partially filled

Q. Tanks that haul milk are:
Ans: Smooth bore tanks

Q. Because a tanker load is so high off the ground:
Ans:
– It will be top-heavy.
– It will have a high center of gravity
– It will roll over easily

Q. The person in charge of loading and unloading a cargo tank with hazardous material must be within __ feet of the tank?
Ans: 25

Q. Never park a tanker carrying explosives “A” or “B” within __ feet of the traveled part of the road:
Ans: 5

Q. A portable tank mounted on a truck or trailer must be at least how many gallons to require you to have a tanker endorsement on your commercial drivers license?
Ans: 1000

Q. What is used to divide a large tank into several smaller tanks?
Ans: Bulkheads

Q. In what type of tank is the liquid surge the most noticeable?
Ans: Smoothbore

Q. Liquids expand as they heat up. You as the driver must leave room for this expansion of the liquid. What is the term used to describe this expansion?
Ans: Outage

Q. What is the major cause of surge?
Ans: Partially filled tanks

Q. A tanker with a high center of gravity is preferred over a tanker with a low center of gravity.
Ans: False

Q. A tank vehicle is described as a vehicle that is used to carry liquids or gases of __ gallons or more.
Ans: 1000

Q. You are driving a tanker that is 3/4 full. If you are forced to brake hard what can you expect to happen?
Ans: The vehicle will be pushed forward and then backward by the liquid surge

Q. Baffled liquid tanks have bulkheads?
Ans: With holes in them to let liquid flow through them

Q. If an oncoming vehicle drifts into your lane you should?
Ans: Move to your right

Q. When you’re driving cargo tank vehicles you must inspect the cargo within the first – of a trip.
Ans: 50 miles

Q. Compared to normal trucks loaded tank trucks must have – Center of gravity.
Ans: A higher

Q. Generally empty trucks?
Ans: Require greater stopping distance then full ones

Q. Transporting liquids tanks require special care for two reasons one reason is the – center of gravity?
Ans: Higher

Q. Except when you’re loading or unloading a cargo tank liquid discharge valves on the compressor gas tank should always be?
Ans: Closed

Q. Which of the following is the best way to drive thru a curve?
Ans: Slow to safe speed before entering in then accelerating slowly through it

Q. Portable tanks?
Ans: Are not Permanently attached to the truck

Q. When loading or unloading a cargo tank a qualified person must be watching from a distance of no farther then – feet.
Ans: 25

Q. You’re driving on the clear night and using your low beam headlights if your headlights let you see about 250 feet ahead of you you should adjust your speed so you can stop in – feet.
Ans: 250

Q. What does liquid surge do to the handling of a tanker?
Ans: It can move the truck in a direction in which the waves move

Q. Which of these statements is true about emergency steering and tankers?
Ans: When making a quick steering movement do not apply the brakes

Q. An emergency forces you to stop your tanker quickly or crash you should?
Ans: Use controlled or stab braking

Q. You’re loading a cargo tank equipped with bulkheads when you load the smaller tanks you should check your?
Ans: Weight distribution

Q. Vehicle skids are often caused by?
Ans: Driving too fast for conditions

Q. Tanks that are not used to transport food products for example milk are?
Ans: Not allowed to have baffles

Q. Generally empty trucks?
Ans: Require greater stopping distance then full ones

Q. Tankers that are used to transport liquid food products?
Ans: Often have very strong front to back surge

Q. To control surge when stopping a tank vehicle you should?
Ans: Not release the brakes too soon

Q. Forward to back surge can?
Ans: Slow a stop truck into the intersection

Q. You are driving a tank truck and the front wheels begin to skid which of the following will most likely occur?
Ans: The truck will continue in a straight line regardless of how much you steer

Q. Which of these air brake system shut-off valves should be closed before beginning to drive a truck that is transporting a tank trailer?
Ans: Back

Q. You should be extremely cautious when driving smooth bore tanks when you are?
Ans: Starting or stopping

Q. When loading the individual tanks of a tanker there is equipped with bulkheads you should make sure that?
Ans: All the tanks are filled evenly

Q. If you steer a tank vehicle quickly while breaking you?
Ans: This may cause the vehicle to roll over

Q. Before loading unloading or driving a tanker the first thing you should do is?
Ans: Inspect the vehicle

Q. When inspecting pipes connections and hoses for leaks pay special attention to?
Ans: Joints

Q. Which of these statements is true about tank vehicles?
Ans: The posted speed for a curve may be too fast for a tank vehicle

Q. Which of these statements is true?
Ans: You should never load a cargo tank totally full

Q. You should know the outage amount for the liquids you carry because?
Ans: Some liquids expand more than others when they get one

Q. If your drive wheels begin to skid when you are towing a tank trailer?
Ans: Your vehicle may jackknife

Q. How many identical placards must be placed on a vehicle?
Ans: Four

Q. Carrying gases or liquids in a leaking tank is:
Ans: Illegal.

Q. When the vehicle is being operated, vents:
Ans: Should be clear.

Q. Tanks have a high center of gravity, which means:
Ans: They can roll over easily

Q. When coming to a stop, the liquid in a tank may surge. This can:
Ans: Cause the truck to be pushed forward.

Q. When loading a tank that is divided into smaller tanks by bulkheads, the load should be:
Ans: Heaviest in the middle.

Q. Smooth bore tanks have:
Ans: Nothing inside to slow the flow of liquids.

Q. Which type of product is usually transported by unbaffled tanks?
Ans: Food

Q. Cargo tanks should never be completely full because:
Ans: There needs to be room for the liquid to expand.

Q. Liquids expand:
Ans: At different rates.

Q. When carrying more than 500 gallons of flammable liquid in a tank truck, a driver may drive no
more than __ within a single work period.
Ans: 10 hours

Q. Tanks equipped with baffles may still roll over because:
Ans: There may be significant side-to-side surge

Q. When loading or unloading a tank that is divided by bulkheads, the person loading the tank
should be mindful of:
Ans: Equal weight distribution.

Q. When loading liquid cargo, you should take into account:
Ans: The weight of the liquid.

Q. The amount of liquid cargo being loaded into a tank should depend on:
Ans: Legal weight limits.

Q. When loading liquid cargo, you should keep in mind:
Ans: How much the liquid will expand in transit.

Q. If you must make a quick stop while transporting liquids, one safe option is to:
Ans: Use the controlled braking method, or Use the stab braking method.

Q. If you must use the controlled braking method while transporting liquid cargo, you should:
Ans: Apply the brakes as hard as possible without locking the wheels.

Q. If you must use the stab braking method while transporting liquid cargo, you should:
Ans: Apply the brakes completely until the wheels lock up, release the brakes until the wheels
start rolling, then repeat the process.

Q. Before operating a tank vehicle, it is important to:
Ans: Check grounding and bonding cables.

Q. To drive safely, it is important to remember:
Ans: How much distance your vehicle needs to stop.

Q. You can lower the risk of jackknifing by:
Ans: Steering smoothly.

Q. How many hazardous materials classes are there?
Ans: Nine

Q. If you are transporting explosives and your vehicle breaks down, you may notify other drivers:
Ans: With electric lights.

Q. An improperly placarded vehicle can only be moved:
Ans: During an emergency.

Q. To operate a vehicle that is used to transport hazardous materials, a driver must have
Ans: A CDL with a hazardous materials endorsement.

Q. On a shipping paper describing both hazardous and non-hazardous materials, the hazardous
materials may be identified by being:
Ans: Listed first

Q. In general, before loading or unloading any flammable liquids, an engine should be:
Ans: Turned off.

Q. When loading compressed gas, the liquid discharge valves should be:
Ans: Opened.

Q. When checking a tank vehicle, it is most important to verify that:
Ans: There are no leaks.

Q. Before driving a tank, you should:
Ans: Check pipes, connections, and hoses for leaks.

Q. What do bulkheads do?
Ans: Separate one large tank into several smaller tanks

Q. Baffled tanks:
Ans: Contain bulkheads with holes, allowing liquid to move among sections of the tank.

Q. A fully-loaded tank vehicle:
Ans: Requires less room to stop than an empty vehicle.

Q. A tank endorsement is:
Ans: Required to transport both liquids and gases.

Q. If a spill occurs from a tank vehicle you are operating:
Ans: You may have to pay for clean-up efforts.

Q. A surge may occur when:
Ans: Liquid cargo quickly moves to the front or rear of a tank.

Q. When driving a tank vehicle, the driver should:
Ans: Increase their usual following distance.

Q. To help control liquid surge, a driver should:
Ans: Brake well in advance of a stop.

Q. Manhole covers:
Ans: Should be closed when a vehicle is being driven.

Q. Due to the risk of liquid surge in tanks, you should:
Ans: Accelerate slowly.

Q. Liquid surge occurs in:
Ans: Partially-filled tanks.

Q. Front-to-back surge is usually very strong in:
Ans: Unbaffled tanks.

Q. Before a tank is loaded:
Ans: The vehicle should be inspected by the driver.

Q. When inspecting a tank, a driver should:
Ans: Refer to their specific vehicle’s operator manual.

Q. Because of tanks’ high centers of gravity, drivers of tanks should:
Ans: Reduce their speed on curves.

Q. If a tank is found to be leaking, the driver should:
Ans: Get the leak fixed immediately.

Q. Dense liquids:
Ans: May easily cause a tank to exceed legal weight limits.

Q. To control a surge, brakes should:
Ans: Not be released too quickly after stopping.

 

California CDL Test Questions and Answers – Hazmat

Below you can find questions and their respective answers for the topic “Hazmat”:

 

California CDL Test Questions and Answers – School Bus

Below you can find questions and their respective answers for the topic “School Bus”:

Q. In addition to checking for spare electrical fuses, three red reflective triangles, and a properly charged and rated fire extinguisher, school bus drivers must also inspect the following emergency equipment
Ans: Three red burning flares, a nine-item first-aid kit.

Q. A school bus driver must also check the alternately flashing amber lights indicator, if equipped, the alternately flashing red lights indicator and the strobe light indicator, if equipped.
Ans: True

Q. School bus drivers must also check the following external lights and reflectors:
Ans:
– Strobe light, if equipped, stop arm light, if equipped.
– Alternately flashing amber lights, if equipped.
– Alternately flashing red lights.

Q. If equipped, check the stop arm to see that it is mounted securely to the left front window of the school bus.
Ans: False

Q. Check that the entry door is not damaged and:
Ans: Operates smoothly and closes securely from the inside.

Q. Should the handrails and stop light be checked during a pre-trip inspection?
Ans: Yes

Q. On a pre-trip inspection for a bus, the passenger/entry should be checked for:
Ans: Door operation, handrails, entry step condition and handicap lift if equipped

Q. When checking a handicapped lift the things that you should look for are:
Ans: Leaking, damaged, or missing parts and explain how the lift should be checked for correct operation. The lift must be fully retracted and latched.

Q. Make sure that all emergency exits are not damaged, operate smoothly, and close securely from the outside.
Ans: False

Q. Check all emergency exits and show that:
Ans: They are not damaged, operate smoothly, and close securely from the inside and the warning devices are working.

Q. During the pre-trip inspection, you should check for broken seat frames and check that seat frames are firmly attached to the floor
Ans: True

Q. Should you check passenger exit mirrors?
Ans: Yes

Q. During the external inspection of a Coach or Transit Bus a check should be made to see that:
Ans: The vehicle is sitting level (front and rear) and if air-equipped, check for audible air leaks from the suspension system.

Q. A compartment check includes:
Ans: Checking that baggage and all other exterior compartment doors are not damaged, operate properly, and latch securely

Q. A battery/box check is important. The battery must be secure, connections must be tight and cell caps must be present. In addition, these items should be checked:
Ans: Battery connections should not show signs of excessive corrosion and the battery box and cover or door should not be damaged and should be secure.

Q. You should activate your alternating flashing amber warning lights
Ans: 100 to 300 feet before the school bus stop

Q. The battery connections should not show signs of excessive corrosion, and the battery box and cover or door should not be damaged and should be secure.
Ans: True

Q. Who is the person in charge and must accept responsibility for supervising and controlling students while on the bus route?
Ans: The bus driver

Q. It is vital to properly adjust and use all mirrors for safe
operations of the school bus
Ans: In order to observe the danger zone around the bus and look for students, traffic, and other objects in this area

Q. The blind spot behind the bus could extend to how many feet?
Ans: 400

Q. The percentage of parents in which the school bus driver is the only person for whom the parents have contact with out of the entire school system can be as high as:
Ans: 85%

Q. By law, the bus warning lights must only be used when:
Ans: Stopping to unload students.

Q. The safest way to stop unruly behavior on the bus is:
Ans: Pull off the road in a safe location, secure the bus, stand up and tell the students what behavior you expect of them.

Q. Immediately after stopping you should:
Ans: Tell the students to stand back until you are ready for them to load.

Q. Which of the following is a reason to evacuate the school bus?
Ans: The bus is stalled on the railroad tracks but there is no train in sight.

Q. The danger zone is the area on all sides of the bus where children are in the most danger of being struck, which of these statements is true about the danger zone:
Ans:
– The danger zones may extend as much as 30 feet from the front bumper with the first
10 feet being the most dangerous.
– The danger zones may extend 10 feet from the left and right sides of the bus, in
addition, the area to the left of the bus is always considered dangerous because of
passing cars.
– The danger zones may extend 10 feet from the rear of the bus.

Q. What would you do if you cannot account for all of the
students you have picked up on your school route?
Ans: Secure the bus, take the key, step outside the bus to check around and underneath the bus.

Q. When stopping on a railroad crossing, the driver must stop no closer than:
Ans: 15 feet.

Q. If a child misses his designated unload site/bus stop and continues riding the bus you should:
Ans: Radio the dispatcher for direction and follow local procedure.

Q. What is the most important reason for doing a school bus inspection?
Ans: For safety as required by Federal, State, and local laws.

Q. Which of the following statements about the bus evacuation procedure is true?
Ans: If time allows, notify the dispatcher of the evacuation location, conditions, and type of
assistance needed.

Q. The most dangerous time during the school bus trip is:
Ans: When students are loading and unloading.

Q. Anti-lock brakes:
Ans: Keep your tires from locking-off during hard brake application.

Q. You should adjust all of the outside left and right side FLAT mirrors to see:
Ans: 200 feet behind the bus or 4 bus lengths behind the bus, along the sides of the bus, them rear tires touching the ground.

Q. When checking the handicap lift the things you should look for are:
Ans: Leaking, damaged, or missing parts, and make sure that the lift is fully retracted and latched.

Q. What color are all school buses painted?
Ans: National school bus yellow.

Q. Most states require a school bus driver to take a physical examination:
Ans: Annually.

Q. If your school bus stalls on the tracks at a railroad crossing you should:
Ans: Evacuate the bus and move students away from the tracks on the angle toward the oncoming train.

Q. If a student must cross the street when they get off the bus which of these statements is true?
Ans: Bus driver should make eye contact with the student and the student should wait for the driver’s signal that it is safe to proceed.

Q. A school bus must have at a minimum how many emergency exits?
Ans: 4

Q. The outside left and right CONVEX mirrors should be adjusted so you can see:
Ans: The entire area to the rear of the mirror along the side of the bus.

Q. When you conduct a post-trip inspection:
Ans: You should walk both through and around the bus.

Q. Before crossing any highway railroad crossing in a school bus be sure that the bus has enough containment to completely clear the railroad tracks. As a general rule, how much space is considered to be an acceptable amount of containment for a school bus?
Ans: The length of the bus plus 15 feet

Q. What is a passive railroad crossing?
Ans: A railroad crossing that does not have any type of traffic control device.

Q. Which of the following is recommended procedure when unloading students?
Ans: Tell the students to remain seated until they are told to exit

Q. You should position the OUTSIDE RIGHT AND LEFT CONVEX MIRRORS to see:
Ans: The entire side of the bus up to the mirror mounts, the front of the rear tires touching the ground, at least one traffic lane on either side of the bus.

Q. The last step you should perform before picking up students at a bus stop is:
Ans: Make a final check to confirm all traffic stops before opening the bus door and signaling students to approach.

Q. Make a final check to confirm all traffic stops before opening the bus door and signaling students to approach.
Ans: No closer than 15 feet and no farther than 50 feet from the nearest rail, where you have
the best view of the tracks.

Q. The OVERHEAD INSIDE REARVIEW MIRROR should be positioned so that you can see:
Ans: The top of the rear window in the top of the mirror, all of the students, including the heads of the students right behind you.

Q. The OUTSIDE LEFT AND RIGHT CROSSOVER MIRRORS should be adjusted so that you can see:
Ans:
– The area from the front of the bus to the service door.
– The right and left front tires touching the ground.
– The entire area in front of the bus from the front bumper at ground level to a point
where direct vision is possible, direct vision and mirror view vision should overlap.

Q. As a general rule, student safety and control is best
maintained by keeping students on the bus during an
emergency and/or impending crisis situation, however, the bus driver must evacuate the bus during mandatory
evacuation situations. Which of the following would qualify as mandatory evacuation situations?
Ans:
– The bus is on fire or there is a threat of fire.
– The bus is stalled on or adjacent to a railroad highway crossing.
– There is an imminent danger of a collision.
– There is a need to quickly evacuate because of a hazardous materials spill.
– The position of the bus may change and increase the danger.

Q. Which of the following statements about special dangers of loading and unloading students is true?
Ans: Students should be told to leave any dropped objects and move to the point of safety out of danger and get the driver’s attention before retrieving the object

Q. The golden rule for school buses when approaching and crossing railroad tracks is:
Ans: Stop, Look, and Listen.

Q. When approaching a school bus stop you should activate your alternating flashing amber warning lights at least __ feet before the bus stop:
Ans: 200

Q. Which school bus accidents should be reported?
Ans: All accidents have to be reported.

Q. During an evacuation situation, after you determine which type of evacuation is best the next step you must take is:
Ans: Securing the bus.

Q. Which of the following will confirm that you are driving a vehicle with anti-lock brakes?
Ans: Your bus will have a yellow ABS malfunction lamp on the instrument panel which lights
up when you start the engine

Q. School buses are required by law to be equipped with __ overhead warning lights as a method of controlling traffic at a school bus stop.
Ans: 8

Q. Which two factors contribute to school buses being one of the safest means of transportation?
Ans: Vehicles and drivers

Q. In addition to checking for spare electrical fuses, three red reflective triangles, and a properly charged and rated fire extinguisher, the school bus driver must also inspect the following emergency equipment:
Ans: Three burning red flares and a nine-item first-aid kit

Q. How should you brake when driving a bus with ABS brakes?
Ans: Apply the brakes as you always have, using only braking force necessary to stop safely and stay in control.

Q. When unloading students, how should you tell the students to exit the bus?
Ans: Walk at least 10 feet away from the side of the bus to a position where the driver can plainly see all students

Q. What should you do if you have lost ABS control at one or more wheels?
Ans: Drive and brake as you normally would because you still have regular brakes but get the system serviced soon.

Q. You must pass the following written tests in order to be a school bus driver:
Ans: CDL General Knowledge, Passenger Endorsement, and School Bus Endorsement.

Q. You should do which of the following when driving a school bus in high wind conditions?
Ans:
– Keep a strong grip on the steering wheel and try to anticipate gusts.
– Slow down to lessen the effect of the wind, or pull off the roadway and wait.
– Contact your dispatcher to get more information on how to proceed.

Q. The OVERHEAD INSIDE REARVIEW MIRROR is mounted directly above the windshield on the driver’s side area of the bus and is used to monitor:
Ans: Passenger activity inside the bus.

Q. At bus stops where more than one student is unloading which procedure is most likely to prevent an unloading obstacle?
Ans: The driver counts the number of students while unloading to confirm the location of all students before pulling away from the stop.

Q. Why are loading and unloading procedures so critical?
Ans: More students are killed while getting on or off a school bus each year than are killed as passengers inside of a school bus.

Q. All mirrors should be viewed in what manner?
Ans: In a logical sequence to ensure that a child, object, or traffic are not in any of the
danger zones.

Q. When handling an unruly student the NEXT step after securing the bus and taking the ignition key with you if you leave your seat is:
Ans: Stand up and speak respectfully to the offender in a courteous manner with a firm voice reminding him of expected behavior, showing him that you mean business. If a change of seating is needed, request that the offender move to a seat near you.

Q. You should activate your hazard lights approximately __ feet before the railroad crossing making sure that your intentions are known.
Ans: 200

Q. During unloading and loading of students you should check your mirrors:
Ans: Continuously.

Q. If the gate comes down as you start to cross the railroad highway crossing you should:
Ans: Drive through it even if it means you will break the gate

Q. When exiting a school bus and crossing the street in front of the bus which procedure should students follow before reaching the edge of the roadway:
Ans:
– Walk approximately 10 feet away from the side of the school bus to a position where
you can see them.
– Walk to a location at least 10 feet in front of the right corner of the bumper, but still
remaining away from the front of the school bus
– Stop at the right edge of the roadway, you should be able to see the students’ feet.

Q. What is the proper procedure for backing a school bus if no lookout is available?
Ans: Set the parking brake. Turn off the motor and take the keys with you. Walk to the rear of the bus to determine whether the way is clear

Q. A school bus can have up to a _ tail swing.
Ans: 3 ft.

Q. Which of these statements about OUTSIDE RIGHT AND LEFT FLAT MIRRORS are true?
Ans:
– These mirrors are mounted at the left and right front corners of the bus at the side or
front of the windshield.
– They are used to monitor traffic, check clearances and students on the sides and to the
rear of the bus.
– There is a blind spot immediately below and in front of each mirror and directly in back
of the rear bumper which extends 50-150 feet and may extend up to 400 feet.

Q. If you believe a railroad crossing signal is malfunctioning what should you do?
Ans: Call your dispatcher to report the situation and ask for instructions on how to respond.

Q. Which of these statements is true about backing a school bus?
Ans:
– Backing a school bus is strongly discouraged and should be only performed if you have
no other safe way to move the vehicle
– You should never back a school bus when students are outside of the bus.
– Backing is dangerous and increases the risk of collision.

Q. Which of these statements is true about ABS?
Ans:
– ABS only comes into play when a wheel would normally have locked up because of
over-braking.
– ABS will help maintain vehicle control, but not always shorten the stopping distance.
– ABS won’t prevent power or turning skids-ABS should prevent brake-induced skids but
not those caused by spinning the drive wheels or going too fast in a turn

Q. OUTSIDE LEFT AND RIGHT CONVEX MIRRORS provide a view of:
Ans: Traffic, clearances, and students at the side of the bus; but do not accurately reflect their size or distance from the bus.

Q. When approaching the stop, bring the bus to a full stop with the front bumper at least _ feet away from students at the designated stop.
Ans: 10

Q. When approaching the stop you should turn on your right turn signal indicator about _ feet before pulling over:
Ans: 100-300

Q. What should you be looking for when conducting your post-trip inspection?
Ans: Articles left on the bus, sleeping students, open windows and doors, mechanical/operational problems with special attention to items unique to school buses, and damage or vandalism.

Q. When approaching the stop you should:
Ans: Place the transmission in Park, or if there is no Park shift point, in Neutral and set the parking brake at each stop.

Q. The OUTSIDE LEFT AND RIGHT SIDE CROSSOVER MIRRORS are used to see:
Ans: The front bumper “danger zone,” the “danger zone” to the left and right side of the bus including the service door and the front wheel area.

Q. You should deal with on-bus problems such as unruly students while stopped to load or unload?
Ans: False. Loading and unloading requires all your concentration. Don’t take your eyes off of what is happening outside the bus. Wait until the students unloading are safely off the bus and have moved away.

Q. At a multiple-track railroad crossing you should stop:
Ans: Only before the first sets of tracks.

Q. When stopping at the railroad crossing you should:
Ans: Place the transmission in Park, turn off all radios and silence all passengers, open the service door and driver’s window. Look, and listen for an approaching train.

Q. How far should you stop from the draw of a drawbridge that has no signal light or control attendant?
Ans: 50 feet

Q. How can you tell when you have a tire blow out?
Ans: Sound, vibration, and feel.

Q. How far can you see with your high beams on?
Ans: 350 to 500 feet.

Q. How far can you see with your low beams on?
Ans: 250 feet.

Q. What is the area between you and other cars on the road?
Ans: Space cushion.

Q. What is the distance it takes to stop once the brakes are applied?
Ans: The braking distance.

Q. What is the distance traveled when your brain tells your foot to move from the accelerator and is actually applying the brakes?
Ans: Reaction time.

Q. Why a driver reacts to certain driving conditions based on habits or past experiences?
Ans: Conditioned response.

Q. When are you required to pull over and allow other vehicles to pass?
Ans: 5 or more.

Q. What are the two factors that can prevent a driver and vehicle from becoming involved in a collision?
Ans: Reaction time and braking distance.

Q. What is the ability to understand and become aware of
something that is going to happen or is happening?
Ans: ) Perception.

Q. What is the reaction time from the time a problem is seen to the time the brakes are applied?
Ans: 3/4 three quarters of a second.

Q. What are the zones of a safety circle?
Ans: Zone of recognition, action, and accident.

Q. What is the proper hand placement on the steering wheel of a bus?
Ans: 9 o’clock and 3 o’clock on opposite side of the steering wheel.

Q. What fluids do to you check prior to starting your bus?
Ans: Oil, transmission, power steering, and water

Q. What holds the drive-shaft in place if it breaks?
Ans: Drive-shaft Guard.

Q. What do you hear when you check your ABS system?
Ans: 8 pops.

Q. What tires can only be used on the rear axle of a school bus?
Ans: Recaps or retreads.

Q. What is the check for unusual items dangling under the bus or excessive fluid leaks?
Ans: The approach.

Q. How much air pressure can you lose on the applied pressure test?
Ans: 3 psi

Q. How much air can you lose on the static test?
Ans: 2 psi

Q. What is the distance your vehicle moves from the time your eyes see a hazard until your brain knows it?
Ans: Perception Distance

Q. At what psi must the low air warning devices activate in the basic air brake system?
Ans: 55-75 psi.

Q. What are the governor cut in and cut out pressures?
Ans: 85 and 130 psi.

Q. When does the low air pressure warning devices in the DAS brake system activate by?
Ans: 60 psi.

Q. What tires should not be used on a school bus?
Ans: Exposed or damaged cords.

Q. The wet tank is the first of three air reservoirs (tanks) in the school bus.
Ans: True

Q. What do you check your tires for?
Ans: Abrasions, Bulges, and Cuts (ABC).

Q. What is used for ventilation and as emergency exits?
Ans: Roof Hatches

Q. Which gauge should you watch as you start your bus?
Ans: Oil gauge.

Q. What is the name of the device that removes moisture and contaminants from the air system?
Ans: Air dryer

Q. When does the safety valve release pressure?
Ans: 150 psi.

Q. How much air pressure can you lose in the initial application during the brake test?
Ans: 10%

Q. When should a driver not operate a school bus?
Ans: Fatigue, Illness, or any other cause. You should not take medications and operate a school bus.

Q. What is required of the bus driver before departing with their group on a field trip?
Ans: Safety speech

Q. When can a driver on an activity trip discontinue operation?
Ans: Reduced visibility.

Q. How soon can you restart your bus prior to departing from a school location?
Ans: 30 seconds

Q. What are the additional hours that a driver can be permitted to drive after encountering adverse weather conditions?
Ans: Not more than two hours.

Q. How many hours can you drive within a work period and when you must stop working?
Ans: 10 and 16

Q. When can the interior lights of a school bus be turned on?
Ans: Whenever deemed necessary

Q. When do the students become the driver’s responsibility?
Ans: As soon as you can recognize them.

Q. Which passenger stops are prohibited for a school bus?
Ans: Left-hand side of any highway and multiple-lane highways where pupils must cross.

Q. School bus stops are prohibited from being located how close to a railroad crossing?
Ans: 200 feet

Q. What should you use to escort pupils across the roadway?
Ans: A handheld stop sign.

Q. When shall the DMV revoke, or suspend a school bus certificate?
Ans: If a driver is convicted of any sex offense.

Q. Prior to driving, what are some of the items you should check the interior of the bus for?
Ans:
– Students or other passengers.
– Trash or clothing.
– School books and student belongings

Q. You must stop at least 25 feet from the draw of a draw bridge.
Ans: False

Q. You do not have to stop at drawbridges if there is no attendant on duty.
Ans: False

Q. You do not need to stop, but must slow down and make sure it’s safe at drawbridges when there is a traffic light showing green or there is a traffic attendant/officer that controls traffic
Ans: True

Q. A driver who misses a child’s unloading stop along the route should
Ans: Radio the dispatcher for directions and follow local procedures

Q. Which of the following statements about bus evacuation procedure is true?
Ans: If time allows, notify the dispatch office of evacuation location, conditions, and type of assistance needed

Q. Which of the following is a recommended procedure when unloading students at school?
Ans: Have the students remain seated until they are told to exit

Q. The most dangerous times during a school bus ride are
Ans: When loading and unloading students

Q. When stopping at a railroad-highway crossing, drivers must stop no closer than
Ans: 15 feet from the track (Anywhere from 15-50 feet)

Q. If students must cross the street when they get off the bus, which statement is true?
Ans: Before crossing, students should make eye contact with the bus driver and wait for the driver’s signal that its safe to proceed

Q. You should adjust the outside of the left and right side flat mirrors to see
Ans: 200 feet behind the bus

Q. If the gate comes down as you are starting across a railroad-highway crossing, you should
Ans: Drive through the gate

Q. Which of the following procedures should be followed when driving a school bus in high winds?
Ans: Keep a strong grip on the steering wheel and try to anticipate

Q. During loading and unloading students you should check your mirrors
Ans: Continuously

Q. The CDL manual indicates the last step in picking up students at the bus stop is to
Ans: Make a final check to confirm all traffic has stopped before opening the bus door and signaling to students to approach

Q. Which of the following statements about special dangers of loading and unloading is true?
Ans: Students should b told to leave any dropped object and move to a point of safety out of the danger zones and get the driver’s attention to retrieve the object

Q. After deciding the type of evacuation that is necessary, the next step you must take is
Ans: Securing the bus

Q. What is the safest way to handle unruly behavior on the bus?
Ans: Pull of the road in a safe direction, secure the bus, stand up and firmly tell the students what behavior you expect of them

Q. Which of the following information will confirm you are driving a vehicle with anti-lock brakes
Ans: A yellow ABS malfunction lamp on the instrument panel will light when you start the engine

Q. Anti-lock braking systems
Ans: Keep your wheels from locking up during hard brake applications

Q. At bus stops where more than one child is unloaded, which is procedure is most likely to prevent an unloading accident?
Ans: Driver counts sts before students as they disembark, and recount before moving bus

Q. Which of the following is a reason to evacuate a school bus?
Ans: The bus is stalled on railroad tracks and there is no train in sight

Q. The blind spot behind the bus could extend up to __ feet behind the bus
Ans: 200

Q. Which of the following statements best explains what to do when a school bus stalls on tracks at the railroad-highway crossing?
Ans: Driver should evacuate bus and move students away from the tracks on an angle toward the oncoming train

Q. You should never change the location of a bus stop without written approval from your school district?
Ans: True

Q. How many feet around the entire bus are considered the danger zone?
Ans: 10 feet

Q. What is the last step you should do, to load the bus safely?
Ans: Monitor all mirrors

Q. How does ABS help?
Ans: Helps avoid wheel lock-up and maintain control

Q. When approaching a bus stop, how many feet before the students should you stop?
Ans: 10 feet

Q. If the ABS malfunction, you still have regular brakes. You may drive the bus but get serviced soon.
Ans: True

Q. You should consider evacuating the bus if
Ans: Fire or danger of fire, smell of leaking fuel, bus could be hit by other vehicles

Q. What endorsement does a CDL driver not need to drive a school bus?
Ans: H endorsement

Q. If you miss a student’s bus stop, what should you do?
Ans: Radio dispatch ask for directions or local procedures

Q. How many feet should you activate your hazard lights when approaching crossing
Ans: 200 feet

Q. When you intend to turn, you should activate the appropriate turn signal at least
Ans: 100 ft advance of the turn

Q. The blind spot behind the bus could extend to how many feet of space
Ans: 400 ft

Q. The area to the left and right of the corner of the bus which may no be seen by the driver in the rearview mirrors is called
Ans: Blind spot

Q. If convex mirrors are properly adjusted, you should be able to see
Ans: at least on traffic lane on either side

Q. When stopping at a railroad crossing, you should
Ans: Stop no closer than 15 ft

Q. Students have been injured or killed during unloading when
Ans: Their clothing, accessories, and even body parts get hung up in the handrail

Q. ABS will compensate for bad brakes or poor brake maintenance
Ans: False

Q. Where are the danger zones around the bus
Ans: Front, back, both sides

Q. What are left and ride side crossover mirrors used for
Ans: To see the entire area in front of the bus

Q. Where are the convex mirrors located
Ans: On the bottom of the flat mirrors on both sides of the bus

Q. When approaching a bus stop, you should?
Ans: Activate school bus lights 300 ft before stop, contionusly check mirrors, stop 10 ft before the stop

Q. If there is a serious behavior problem on the bus, you should
Ans: Call for assistance if necessary

Q. Outside flat mirrors are used for
Ans: To monitor traffic, check clearances and students on the sides and to the rear of the bus

Q. When loading or unloading students at a school campus you should?
Ans: Have the bus turned off with key out of the ignition switch

Q. You should put your vehicle in Park or Neutral and set your parking brake at each stop
Ans: True

Q. The area to the left side is considered more dangerous than the right side because
Ans: Passing vehicles

Q. A passive railroad crossing does not have any type of traffic control device
Ans: True

Q. When students are crossing at a bus stop they should walk approximately__ feet in front of the right hand corner of the bumper
Ans: 10 feet

Q. Unloading students on your bus route, you should?
Ans: Count heads as they are exiting

Q. ABS will add-on to your normal brakes and increase or decrease your ultimate stopping power
Ans: False

Q. When stopping the vehicle DO NOT PUMP the brake pedal on a bus with ABS brakes
Ans: True

Q. To load students safely and return the bus to the road you should
Ans: Check mirrors for traffic and late students running behind the bus, All school bus lights are turned off, Make sure service door is closed

Q. A post trip inspection is
Ans: inspecting the bus after bus run

Q. The overhead inside rearview mirror is used for?
Ans: To monitor passenger activity

Q. More students are killed while getting on or off a school bus than are killed as passengers inside the bus
Ans: True

Q. It is mandatory to evacuate the bus if stalled on or adjacent to a railroad crossing
Ans: True

Q. To ensure you have proper mirror adjustment, you should
Ans: Check each mirror before operating a bus, be able to see 200 ft or 4 bus lengths behind the bus, See rear tires touching the ground

Q. When doing a post-trip inspection, you should check for
Ans: Articles left on the bus, Sleeping children, Mechanical problems or vandalism

Q. ABS only comes into play when a wheel would lock up because of over braking
Ans: True

Q. If you drive a vehicle with ABS you should
Ans: Drive and brake as you always have

Q. A safe place to unload students in an emergency is?
Ans: At least 100 ft off the road

Q. An ACTIVE railroad crossing has traffic control devices, which can include
Ans: Flashing red lights, flashing red lights with bell, flashing red lights with bells and gates

Q. If the gate comes down at a railroad crossing after you have started across
Ans: Continue through, even if it means you will break the gate

Q. If there is a behavior problem on the bus while unloading
Ans: Pull the bus over to handle the problem, Wait until the students unloading are safely off the bus and have moved away, Don’t take your eyes of what is happening outside the bus

Q. If you believe the control devices at a railroad crossing are malfunctioning
Ans: Call your dispatch to report the situation and ask for instruction on how to proceed

Q. A school bus can have up to _ foot tail swing
Ans: three

Q. Strong winds can push a school bus sideways, even off the road. In extreme conditions, tip ove
Ans: True

Q. A school bus driver is required to carry at all times
Ans: Valid CDL, Current DOT physical card, current certification card

Q. What endorsement must you have to drive a school bus?
Ans:
– School bus endorsement,
– Passenger endorsement, CDL “b”

Q. When merging back into traffic from bus stop you should
Ans: Disengage parking brake, turn on left signal, check all mirrors

Q. If you miss a student’s bus stop, should you back up?
Ans: No

Q. Additional procedures for students that must crossover roadway
Ans: Walk 10 ft out of danger zone, Have students wait for your signal to cross, and look both ways for added safety

Q. When approaching a railroad crossing
Ans: Activate hazard lights 200 ft before railroad, SLow down to a safe speed or downshift, stay to the right of the road

Q. When stopping at railraod, you should
Ans: Stop no closer than 15 ft, put the bus in neutral or park, open service door and driver’s window

Q. Maximum time in transit. No pupil shall be allowed to remain in transit to and from school for
Ans: More than three hours on round trip

Q. Inspection of buses are made one or more times a year to determine whether the school bus can be used to safely transport school children
Ans: True

Q. Each state board of education is charged with primary responsbility of rules and regulations regarding pupil transportation
Ans: True

Q. When must you stop before crossing a drawbridge?
Ans: Stop at least 50 feet before the draw of the bridge

Q. Urban mass transit coaches may have a brake and accelerator interlock system. The rear door of a transit bus has to be open to put the parking brake
Ans: False

Q. If you work as an interstate carrier, you must complete written inspection for each bus driver
Ans: True

Q. Are recapped or regrooved tires allowed on buses?
Ans: Yes, on all wheels except the front wheels

Q. What is the shape of hazardous material labels?
Ans: Diamonds

Q. When student loading, how many feet before stopping should you be if you are going 35+ MPH
Ans: 300 Feet

Q. When student loading, how many feet before stopping should you be if you are going less than 35 MPH
Ans: 100 Feet

Q. When should your strobe lights be used?
Ans: if weather conditions or terrain effect visibility

Q. What should all school buses be equipped with
Ans: First aid kit and body fluids cleanup kit

Q. How many years do you renew your driver’s license?
Ans: 4 Years

Q. How many years do you renew a physical?
Ans: 2 years

Q. How many days is a temporary school bus endorsement effective?
Ans: 180 days

Q. Define school bus
Ans: Motor vehicle used to transport pupils to or from school or school-related activities

Q. What is a disqualifying offense?
Ans: any felony offense, drug violation, 5th-degree criminal conduct, interference with privacy, indecent exposure, or a violation of DWI laws

Q. What is a reportable offense?
Ans: misbehavior causing an immediate and substantial danger to self or surrounding people or property

Q. What is a gross vehicle rating?
Ans: the value specified by the manufacturer as the loaded weight of a single vehicle

Q. How many years will a person lose their privileges to drive a commercial motor vehicle if convicted of consumption of alcohol?
Ans: One Year

Q. True or False: A second conviction will result in loss of commercial driving privileges for life?
Ans: True

Q. Who can waive a permanent cancellation requirement of someone convicted of a misdemeanor, gross misdemeanor, or non-felony violation?
Ans: A commissioner

Q. How many feet should a student be when walking in front of a bus?
Ans: 10 Feet

Q. How many feet should a bus stop when approaching a RR crossing?
Ans: 15 Feet back

Q. Which hazard lights should you use when crossing a railroad?
Ans: 4 ways

Q. How many feet should a driver turn on the four way hazard lights when approaching a railroad crossing?
Ans: 100 feet

Q. What must a driver do when at a railroad crossing?
Ans: Stop, Look, Listen

Q. What are flashing Amber lights (8ways) used for?
Ans: To warn other drivers that the bus is preparing to stop to load or unload

Q. Before loading students, How many feet should you signal right before stopping?
Ans: 100 Feet

Q. How many feet should you stop before reaching the students?
Ans: 6-8 Feet

Q. True/False. A bus should never operate in reverse on school grounds
Ans: True

Q. True/False Students should always walk towards the bus when unloading
Ans: False; Students should always walk away from the bus

Q. When unloading/ loading at a school which hazard lights should be on?
Ans: 4-ways

Q. How many feet away should a driver stop for an extended stop arm?
Ans: 20 feet

Q. A person who violates a stop arm is guilty of what offense?
Ans: A misdemeanor

Q. What punishment could a person receive if passing an extended stop arm?
Ans: A $300 fine, also driving privileges suspended

Q. If a person passes an extended stop arm two or more times within five years what could happen?
Ans: Their driving privileges could be revoked

Q. When should you evacuate a bus?
Ans: Fire, Unsafe position, or Danger of drowning

Q. Under what two circumstances are you able to transport students after an accident occurs?
Ans: It has been inspected by the Minnesota State Patrol, or it has been granted a waiver by the state trooper

Q. True/False. A bus driver who gives care, advice, or assistance at the scene of an emergency is NOT liable for any civil damage
Ans: True

Q. True/ False. When backing up a bus driver should activate their 4-ways
Ans: True, you should be able to see any moving vehicles within 500 feet in either direction

Q. How many feet following distance should you allow on a highway?
Ans: 500 Feet

Q. What is the proper way to determine the right following distance?
Ans: Count off the seconds it takes from the time the back of the vehicle ahead passes the reference point until the front of your vehicle passes

Q. What is the correct following distance with an interval of 8 seconds?
Ans: 500 feet at 45 MPH

Q. How many seconds will it take to pass another vehicle?
Ans: 10-20 seconds

Q. Define danger zone
Ans: Area on all sides where children are in most danger of being hit

Q. How far may the danger zones extend from the front bumper?
Ans: 30 geet

Q. How far may the danger zones extend from the left and right sides of the bus?
Ans: 10 feet

Q. How far may the danger zones extend from behind the rear bumper?
Ans: 10 feet

Q. How far may the blind spots extend behind the bus?
Ans: 400 feet

Q. What are round yellow warning signs used for?
Ans: Notify the driver to slow down, look and listen for a train and be prepared to stop at the tracks

Q. What do pavement marks consist of?
Ans: An “X” with the letters “RR” and no passing marking on two land roads

Q. The danger zones may extend as much as feet from the bumper
Ans: [30, front

Q. The first __ feet of the danger zone is the most dangerous.
Ans: 10

Q. The area to the _ of the bus is always considered dangerous because of passing cars.
Ans: left

Q. How often should you check each mirror?
Ans: every time you operate the bus

Q. There is a blind spot immediately below and in front of each outside left and right side flat mirror and directly in _ of the _ bumper.
back, rear

Q. The blind spot behind the bus could extend up to __ feet
Ans: 400

Q. Ensure that the outside left and right side flat mirrors are properly adjusted so that you can see _ bus lengths behind the bus.
Ans: 4

Q. True or False: You should ensure that the mirrors are properly adjusted so that you can see the front tires touching the ground.
Ans: False

Q. True or False: Convex mirrors present a view of people and objects that accurately reflect their size and distance from the bus.
Ans: False

Q. The convex mirrors are used to monitor the sides at an angle.
Ans: left and right, wide

Q. The outside left and right side crossover mirrors are mounted on the _ corners of the bus.
Ans: Front

Q. Ensure that the outside left and right side crossover mirrors are properly adjusted so that you can see:
Ans: the area from the front of the bus to the service door

Q. The overhead inside rearview mirror is mounted directly _ the windshield on the ___ side area of the bus.
Ans: above, driver’s

Q. The overhead inside rearview mirror is mainly for monitoring:
Ans: passenger activity inside of the bus

Q. The overhead inside rearview mirror has blind spots directly behind the driver’s seat and:
Ans: behind the rear bumper

Q. You should position the overhead inside rearview mirror so that you can see:
Ans: the top of the rear window in the top of the mirror

Q. When should you change the location of a bus stop?
Ans: Only when you have written approval from the appropriate school district official

Q. Before approaching a stop, if the school bus is so equipped, activate alternating flashing amber warning lights at least _ seconds before the school bus stop or in accordance with state law.
Ans: 5 to 10

Q. When approaching a stop, turn on right turn signal indicator about 100-300 feet or approximately _ seconds before pulling over.
Ans: 3 to 5

Q. When approaching a stop, bring the school bus to a full stop with the front bumper at least __ feet away from students at the designated stop.
Ans: 10

Q. True or False: It is acceptable to place the transmission in neutral if there is no park shift point.
Ans: True

Q. When students are entering the bus, if you notice that there is a student missing, you should first:
Ans: ask the other students where the student is

Q. When students have entered the bus, if you cannot account for a student outside, secure the bus, take the key, and:
Ans: check around and underneath the bus

Q. When all students are accounted for, prepare to leave by __ alternating flashing red lights and __ the left turn signal.
Ans: turning off, turning on

Q. True or False: If you have missed a student’s unloading stop, it is acceptable to back up.
Ans: False

Q. When unloading students, if students must cross the roadway, you should walk to a location at least _ feet in front of the _ corner of the bumper
Ans: 10, right

Q. For students that must cross the roadway, after they reach the roadway, the students should stop at the __ edge of the school bus before proceeding.
Ans: left

Q. When unloading students at a school, the first step is to:
Ans: secure the bus

Q. In total, how many times should you check your mirrors throughout the process of unloading students at a school?
Ans: Twice

Q. When loading or unloading students, if a student drops an object near the bus:
Ans: tell the student who dropped it or attempt to get the parent’s attention

Q. When conducting a post-trip inspection, any problems or special situations should be reported to:
Ans: your supervisor or school authorities

Q. If there is an emergency situation, the first and most important consideration is to:
Ans: recognize the hazard

Q. Bus evacuation is always mandatory in all of the following situations EXCEPT:
Ans: if there is a dangerous individual in the area

Q. Whenever possible, assign ___________ to each emergency exit for evacuations.
Ans: 2 student assistants

Q. When determining evacuation procedures, a safe place will be at least _ feet off the road in the direction of oncoming traffic.
Ans: 100

Q. During evacuation from the bus, lead students upwind of the bus at least ___ feet if there is a risk from spilled hazardous materials
Ans: 300

Q. If the bus is in the direct path of a sighted tornado and evacuation is ordered, the first thing you should do is:
Ans: escort students to a nearby ditch or culvert if shelter in a building is not readily available

Q. During evacuation from the bus, if no radio is available or operable, first __ to call for help.
Ans: dispatch a passing motorist or area resident

Q. When should you move a student you believe may have suffered a neck or spinal injury?
Ans: When the student’s life is in immediate dange

Q. Crossings that have yellow circular advance warning signs, pavement markings and crossbucks to assist you in recognizing a crossing are known as __ crossings.
Ans: passive

Q. ______ crossings include flashing red lights, with or without bells and flashing red lights with bells and gates.
Ans: Active

Q. With _______ crossings, the decision to proceed rests entirely in your hands.
Ans: passive

Q. The round, black-on-yellow warning sign is placed ahead of:
Ans: public railroad-highway crossings

Q. True or False: Pavement markings mean the same as the advance warning sign.
Ans: True

Q. If there is no white line painted on the pavement before a railroad crossing, you must stop the bus before:
Ans: the crossbuck sign

Q. When the road crosses over more than one set of railroad tracks, the sign below the crossbuck sign indicates:
Ans: the number of tracks

Q. _____ indicate(s) that you must stop.
Ans: The flashing red lights of a crossbuck sign

Q. If a railroad-highway crossing gate stays down after a train passes, you should
Ans: call your dispatcher

Q. Activate hazard lights approximately _ feet before a railroad crossing.
Ans: 200

Q. When approaching a railroad crossing, stay ___ the roadway if possible.
Ans: to the right of

Q. When approaching a railroad crossing, stop no closer than _ feet and no farther than _ feet from the nearest rail.
Ans: 15, 50

Q. At a multiple-track railroad crossing:
Ans: stop before the first set of tracks

Q. True or False: If the gate comes down after you have started across a railroad crossing, you should drive through it even if it means you will break the gate.
Ans: True

Q. When crossing railroad tracks, as a general rule, add __ feet to the length of the school bus to determine an acceptable amount of containment or storage area.
Ans: 15

Q. If you must stop the bus to handle a serious problem, an acceptable place would be:
Ans: a driveway

Q. The best tone of voice when speaking with an offender on the bus is:
Ans: firm, courteous

Q. True or False: It is acceptable to ask a student to leave the bus for misbehavior at the school or at the student’s designated bus stop.
Ans: True

Q. If your bus has an antilock braking system, it will have a yellow __ on the instrument panel.
Ans: lamp

Q. Having an antilock braking system on your bus helps you because:
Ans: it allows you to steer around obstacles while braking

Q. With ABS in non-emergency situations, you should brake __ with non-ABS braking.
Ans: the same as

Q. When should you pump the brakes on a bus with ABS?
Ans: Never

Q. On newer vehicles, you may have lost ABS control at one or more wheels if the malfunction lamp __ after the bulb check.
Ans: stays on

Q. If your ABS malfunctions:
Ans: you still have brakes

Q. What will ABS do?
Ans: Help maintain vehicle control

Q. The overhead strobe light should be used:
Ans: when you have limited visibility

Q. If you are caught in strong winds, you should do any of the following EXCEPT:
Ans: relax your grip on the steering wheel

Q. Backing up a school bus is:
Ans: Discouraged

Q. Prior to backing up a bus:
Ans: post a lookout, but not to give directions on backing up the bus

Q. If no lookout is available:
Ans: walk to the rear of the bus yourself

Q. If you must back up at a student pick-up point, be sure to pick up the students __ backing up.
Ans: before

Q. A school bus can have up to a _-foot tail swing.
Ans: 3

Q. You need to check your mirrors and any turning movements to monitor the tail swing
Ans: before, during

Q. To drive a school bus, your vision must be at least
Ans: 20/40 in both eyes

Q. To drive a school bus, you must be at least _ years of age
Ans: 18

Q. To drive a school bus, the greatest number of DWI (Driving While Impaired) convictions you can ever have is:
Ans: 1

Q. A CDL (Commercial Driver’s License) is required to drive any vehicle designed to transport more than _ people (including the driver).
Ans: 15

Q. What is the greatest number of Commercial Driver’s Licenses that one person is allowed to have?
Ans: 1

Q. School bus drivers must notify their employer within ___ calendar days of a conviction for any traffic violation.
Ans: 30

Q. For a bus driver not carrying hazardous materials, DWI (Driving While Impaired) is punishable by a loss of driving privileges for _____ upon the first conviction.
Ans: one year

Q. For a bus driver not carrying hazardous materials, DWI (Driving While Impaired) is punishable by a loss of driving privileges for _____ upon the second conviction.
Ans: life

Q. Any commercial driver who intentionally refuses chemical analysis will lose driving privileges immediately for a minimum period of:
Ans: 30 days

Q. When applying for a commercial driving job, you must provide the prospective employer with a history of all driving jobs you have held during:
Ans: the past 10 years

Q. School bus drivers may use _____________ while operating the bus.
Ans: neither cellular phones nor two-way radios

Q. School bus drivers should have physical contact with students:
Ans: when administering first aid or evacuating the bus

Q. For bus drivers, stopping on the way home for personal reasons is:
Ans: prohibited

Q. If passengers must stand on a moving school bus, they must stand:
Ans: behind the back of the driver’s seat

Q. Who has the authority to appoint a substitute bus driver?
Ans: The school principal only

Q. Who is responsible for keeping a school bus clean on a daily basis?
Ans: The driver

Q. True or False: A school principal may suspend a pupil from riding a school bus for delaying the bus schedule.
Ans: True

Q. When may a school bus driver take the bus off of its regular route?
Ans: With the school principal’s permission or direction

Q. If a school bus passenger misbehaves:
Ans: the school principal should be notified

Q. The _____ has charge of the operations of the school bus garage and responsibility for seeing that each school bus is safe and in sound mechanical condition.
Ans: transportation director

Q. The ______ trains and certifies school bus drivers.
Ans: driver education specialist

Q. True or False: For the purposes of school bus driver certification, a PJC (Prayer for Judgement Continued) is considered by the Division of Motor Vehicles to be the same as a conviction.
Ans: True

Q. School bus drivers should perform a bus inspection:
Ans: before each trip

Q. When inspecting the front of a school bus, the wording should be clean and at least ___ in height.
Ans: 8 inches

Q. When inspecting the right rear brakes on a school bus, the slack adjuster angle between the push rod and adjuster arm should be a little over _ degrees when the brakes are released and not less than _ degrees when the brakes are applied.
Ans: 90, 90

Q. When inspecting the tires on a school bus, the right front tire should have at least ___-inch depth.
Ans: 4/32

Q. A first-aid kit is ________ for school buses.
Ans: required

Q. A school bus horn should be audible for at least _____ feet.
Ans: 200

Q. While driving a school bus, emergency exits should be:
Ans: closed but not locked

Q. The steering wheel on a school bus should have _______ of play on a power steering bus.
Ans: less than two inches

Q. When checking air brakes in a school bus, you should conduct the LAB test, which stands for Leaks, _______, and Button pop-out.
Ans: Alarm

Q. When conducting air brake checks on a school bus, let the air pressure build to the governed cut-out pressure, which is _ pounds per square inch (psi).
Ans: 120

Q. School bus parking brakes and service brakes should both have air pressure in the range of _______ pounds per square inch (psi).
Ans: 90 to 120

Q. When performing a hydraulic brake check for a school bus, the first step is to:
Ans: pump the brake pedal three times

Q. When inspecting under a school bus, check for the frame, exhaust, and _____.
Ans: drive shaft

Q. To move the school bus, the first thing you should do is:
Ans: depress the brake pedal firmly

Q. True or False: To keep from rolling backward on an uphill grade, it is permissible to use your left foot to press the brake while you begin to accelerate with your right foot.
Ans: True

Q. To stop a school bus smoothly:
Ans: feather the brake

Q. In normal weather and road conditions, the minimum following distance for a school bus is:
Ans: 5 seconds

Q. In hazardous weather or road conditions, the minimum following distance for a school bus is:
Ans: 10 seconds

Q. When following two school buses, maintain at least _____ of distance between your bus and the pair ahead.
Ans: one city block

Q. Which one of the following is NOT a component of total stopping distance?
Ans: expectation distance

Q. The distance your vehicle travels between the moment when your eyes physically see a driving hazard and the instant when your brain recognizes the hazard is called the:
Ans: perception distance

Q. The average perception and reaction time for an alert driver is about:
Ans: 3/4 second

Q. For vehicles with air brakes, there is approximately a _____ delay in brake response time from the moment when you press the brake pedal to the point when the brakes engage.
Ans: 1/2 second

Q. A heavy vehicle moving at 55 miles per hour will need a minimum stopping distance about the length of a:
Ans: football field

Q. When a vehicle’s speed of travel is doubled, the braking distance and destructive power in a crash are increased by ____ time(s).
Ans: 4

Q. More collisions occur at ______ than at any other place.
Ans: intersections

Q. When two vehicles arrive at an unregulated intersection at the same time:
Ans: the vehicle on the left always yields right of way to the vehicle on the right

Q. For school buses, turning right on red:
Ans: is not acceptable

Q. A flashing red traffic light is to be treated the same as a:
Ans: stop sign

Q. With a school bus, before entering or crossing any road, look first:
Ans: to the left

Q. The slogan for a school bus driver must be:
Ans: The school bus driver never has the right of way.

Q. Before making a turn with a school bus, engage the turn signal __ feet in advance
Ans: 300

Q. Before making a turn with a school bus, slow gradually to __ mph or less at least 50 feet before the turn
Ans: 10

Q. Backing up a school bus is:
Ans: only to be done when absolutely necessary

Q. Backing up a bus should be done:
Ans: with no acceleration

Q. A safe place for turning around should have at least __ feet of unobstructed visibility in both directions.
Ans: 500

Q. All of the following are methods of turning a bus around EXCEPT:
Ans: the three-point turn-around

Q. The safest method of turning a school bus around is:
Ans: the forward turn-around

Q. True or False: If you are unloading passengers at the turn-around point, back the bus after they are unloaded.
Ans: False

Q. When unloading students at a bus stop, when students are crossing in front of the bus, always check to make sure no one is in front of the bus by:
Ans: counting the passengers

Q. When making a passenger stop in a school bus, stop the bus on the main portion of the road in the extreme ____ lane and be certain to stop _ reaching the waiting passengers.
Ans: right-hand, before

Q. If a parent at a school bus stop attempts to argue with a school bus driver, the school bus driver should:
Ans: ask the parent to contact the principal

Q. If a bus driver passes by a student at a passenger stop, the driver should:
Ans: let the student come to the bus

Q. School bus drivers should always check the __ just before leaving a passenger stop.
Ans: passenger mirrors

Q. Assigning seats to the students on a school bus:
Ans: is recommended

Q. School bus drivers should stop at least _ feet, but not more than _ feet from the track.
Ans: 15, 50

Q. True or False: When turning near a track, a turn signal should be used instead of the hazard lights.
Ans: True

Q. When parking a school bus, the driver should report equipment defects:
Ans: to the principal

Q. When a school bus driver wishes to increase visibility because of rain or snow, the driver should turn on the:
Ans: low beam headlights

Q. A school bus driver should use high beams when the bus is not within _ feet of an approaching vehicle.
Ans: 500

Q. When driving a school bus on wet roads reduce speed by about _, and on packed snow reduce speed to about _.
Ans: one-third, one-half

Q. To correct a drive wheel braking skid in a school bus, do all of the following EXCEPT:
Ans: accelerate

Q. At drawbridges that do not have a signal light or traffic control attendant, school buses should stop at least ___ feet before the draw before crossing.
Ans: 50

Q. Safe drivers look to seconds ahead when driving.
Ans: 12, 15

Q. When driving a school bus, if your speed is above 20 miles per hour and you have to drive off of the road to avoid a collision:
Ans: avoid braking

Q. If you experience brake failure with air brakes in a school bus, you should:
Ans: use the parking brake

 

California CDL Test Questions and Answers – Air Brakes

Below you can find questions and their respective answers for the topic “Air Brakes”:

 

California CDL Test Questions and Answers – Passenger Transport

Below you can find questions and their respective answers for the topic “Passenger Transport”:

Q. The following are some situations that require special attention from all drivers. Which one is an even bigger problem for the driver of a vehicle with a low ground clearance?
Ans: Humps or dips on the road.

Q. The standee line is:
Ans: A two-inch line on the floor to the rear of the driver’s seat in which all riders must stay behind while the bus is moving.

Q. If a rider wants to bring a car battery or a can of gasoline aboard your bus, you should:
Ans: Not allow him to do so.

Q. Off tracking of the rear wheels is caused by:
Ans: Greater distance between the front and rear wheels, sharper turns and curves, faster driving speeds.

Q. Buses may have recapped or re-grooved tires:
Ans: Anywhere except on the front wheels

Q. You have passed all the requirements for a “class B” bus
driver’s license. Which of these vehicles are you not licensed to drive?
Ans: Class A bus

Q. Which of the following answers lists the three types of
emergency equipment you must have on your bus?
Ans: Fire extinguisher, spare electrical fuses, and emergency reflectors.

Q. How are buses supposed to handle most railroad crossings?
Ans: Come to a complete stop before crossing.

Q. You must not permit passengers to stand:
Ans: In front of the standee line.

Q. When driving a bus across the railroad tracks you:
Ans: Should never change gears on a bus with a manual transmission.

Q. Which of these forms of signaling is not recommended?
Ans: Signaling to others that it is safe to pass.

Q. Which of these statements about gear ranges in buses with automatic transmissions is true?
Ans: The lowest ranges should be used for greater engine braking on downgrades.

Q. It is best to wear your seat belt:
Ans: At all times for safety.

Q. A bus may carry baggage or freight only if it is:
Ans: Secured and out of the way of any exits.

Q. Federal regulations do not allow a driver to drive if:
Ans: Ill or impaired, and the condition interferes with his ability to drive.

Q. Which of the following must be closed while the bus is in motion?
Ans: Emergency windows.

Q. As the driver of a bus, how can you best avoid hindering other traffic on the highway?
Ans: By staying in the right lane

Q. Which of the following types of cargo can never be carried on a bus:
Ans: Tear gas or irritating materials.

Q. In general, the best braking technique to use in maintaining a safe speed when driving on a downgrade is:
Ans: Use the snub braking method (5 mph below safe speed).

Q. When you inspect your bus, you must make sure that:
Ans: Rider signaling devices are working properly.

Q. At the end of each shift you should:
Ans: Take all of your personal belongings, inspect the bus and report any defects.

Q. The following is not allowed on a bus:
Ans: Talking with riders while driving or towing a disabled vehicle

Q. You may sometimes haul small arms ammunition, emergency shipments of drugs, or hospital supplies on a bus. The total weight of all such hazardous materials must not be greater than __ pounds.
Ans: 500

Q. An oncoming vehicle keeps its high beams on. You should deal with this hazard by:
Ans: Looking to the right side of your lane.

Q. You must have a CDL if:
Ans: You are going to drive a vehicle that carries over 15 people including the driver.

Q. When carried on a bus, hazardous materials must :
Ans: Be labeled

Q. If your bus becomes disabled on a freeway or expressway and you must stop on the left side of the road, it is best to stop so that the bus is:
Ans: At an angle to traffic with the front door facing the downstream side of traffic.

Q. You need to evacuate your bus in an emergency, passengers should be directed to a safe place no less than __ feet from the bus
Ans: 100

Q. When you are not sure who has the right of way, the safest course of action is to:
Ans: Let the other driver have the right of way

Q. Buses may carry
Ans: Small arms ammunition labeled ORM-D

Q. Charter bus drivers should
Ans: Explain the rules and not allow riders on the bus until departure time

Q. The proper time to cancel your turn signal for a lane change or turn is:
Ans: When the lane change is complete.

Q. A passenger that becomes violent or disruptive should:
Ans: Should not be let off the bus where it would be unsafe for him or her

Q. Which of these is the best general rule for night driving?
Ans: Increase your normal daytime following distance by one second.

Q. If your bus leans toward the outside on a banked curve you are
Ans: Driving too fast.

Q. When you arrive at the bus stop, you should announce:
Ans: Location, reason for stopping, next departure time, and the bus number

Q. Which of the following about speed are true?
Ans: You should be able to stop the distance you can see ahead.

Q. A straight vehicle weighing 20,000 pounds GVWR which hauls 20 passengers falls into which CDL class:
Ans: C

Q. In a pressurized cooling system, coolant level should be checked:
Ans:
– by a mechanic
– every 90 days

Q. You must put a loaded bus into motion from a stopped
position on a steep upgrade (4% or more). Which of these is the best technique to follow when you have a bus with a manual transmission?
Ans: Slowly release the clutch while releasing the parking brake

Q. When you apply for a bus driving job, you must report to the company all motor vehicle accidents you have been involved in during the past __ year (s).
Ans: 3

Q. If your bus has an emergency exit door it must:
Ans: Be secured when the bus is moving.

Q. The driver’s seat should be adjusted:
Ans: Only when the bus is at a complete stop.

Q. The interlock system for the brake and accelerator on a transit coach may be used:
Ans: As a safety feature when the exit door is open.

Q. When driving at more than 40 mph, what is the safe minimum following distance for ideal daytime conditions?
Ans: Four seconds plus one second

Q. All of the following should be in good working order before driving. Which item must be in good working order before the bus can leave?
Ans: Service brakes.

Q. If you increase your speed from 20 to 60 mph (original speed times 3), how much more braking distance is required at 60 mph than at 20 mph?
Ans: 3 x 3 or 9

Q. Name some things to check in the interior of a bus during the pre-trip inspection.
Ans:
– Parking brake and steering mechanism
– Lights, reflectors, and horns.
– Tires and windshield wipers.

Q. As you check the outside of the bus, you should close any open emergency exits or open access panels.
Ans: True

Q. Most hazardous materials cannot be carried on a bus, but some hazardous materials are allowed.
Ans: True

Q. What are some hazardous materials you can transport by bus?
Ans: Small arms ammunition, hospital supplies, and hospital drugs.

Q. In buses designed to allow standing you can stand anywhere you want.
Ans: False

Q. Does it matter where you make a disruptive passenger get off the bus?
Ans: Yes

Q. What are “prohibited practices” while operating a bus?
Ans:
– Fueling with riders on board.
– Talking to riders while driving.
– Towing or pushing a disabled bus with riders aboard.

Q. Urban mass transit coaches may have a brake and accelerator interlock system. The rear door of a transit bus has to be open to put on the parking brake.
Ans: False

Q. If you work as an interstate carrier, you must complete a written inspection report for each bus driver.
Ans: True

Q. Before driving who is responsible for inspecting emergency equipment?
Ans: The driver

Q. What are the shape of hazardous material labels?
Ans: Diamond-shaped.

Q. Which poor weather condition can cause the most dangerous driving?
Ans: Ice

Q. If you have to swerve quickly to avoid an accident you want to know:
Ans: Where other vehicles are around your bus.

Q. You do not have to stop but slow down for the following railroad crossings:
Ans:
– At crossings marked as “Exempt” or “Abandoned”
– At railroad crossings used only for industrial switching within a business district.
– If a traffic signal shows green.
– At streetcar crossings.
– Where a policeman or flagman is directing traffic

Q. You do not have to stop at a drawbridges that do not have a signal light or traffic control attendant.
Ans: False.

Q. If you have riders aboard, you should never fuel your bus:
Ans: Inside a closed building.

Q. You are driving at night and you must dim your headlights from high to low beam. How should you adjust your speed?
Ans: Slow down.

Q. You work for a different state area. You must complete the post-trip inspection report that specifies:
Ans: Any problem that would affect safety or result in a breakdown.

Q. Which of these most affects the amount of traction your bus has?
Ans: The type and condition of the road surface.

Q. When braking, a bus will have the most traction when:
Ans: The wheels are rolling, just short of locking.

Q. While driving a bus you should:
Ans: Scan the interior of your bus as well as the road ahead, to the side, and to the rear

Q. Carry on baggage:
Ans: Can never be left in a doorway or in an isle.

Q. You should remind riders to take their belongings with them if they get off the bus. It is best to tell them:
Ans: Before coming to a complete stop.

Q. Many buses have curved (convex or spot) mirrors. These mirrors:
Ans: Make things seem smaller and further away than they really are.

Q. How many folding aisle seats are allowed in a bus that is not carrying farm workers?
Ans: 0

Q. Which of these statements about hazards is true?
Ans: Movement inside a parked car could mean that a person is about to step out of it

Q. You must sign the inspection report made by the previous driver only when:
Ans: Defects reported have been certified as repaired or not needing repaired

Q. Which of these actions will result in the best control on
curves?
Ans: Slow to a safe speed before entering curves, and then accelerate slightly through curves

Q. When should you check your mirrors for a lane change?
Ans: Regularly as a part of your check for potential hazard.

Q. You are driving a 30-foot bus on a highway. The road is dry and visibility is good. The distance between you and the vehicle ahead of you should not be less than _ seconds.
Ans: 4

Q. To stop for railroad tracks, you should stop _ feet before the nearest track.
Ans: 15 to 50.

Q. Which of these statements about speed management and braking is true?
Ans: You need about FOUR times as much stopping distance at 40 mph than as at 20 mph.

Q. You are driving a 40-foot bus at 50 mph. The road is dry and visibility is good. You should keep a safety space in front of your bus that is at least _ seconds.
Ans: 5 seconds.

Q. When driving a bus how far ahead should you look?
Ans: 12-15 seconds

Q. When you discharge an unruly passenger, you should pick a place that is:
Ans: As safe as possible.

Q. Buses may carry 500 total pounds of allowed hazardous materials, but no more than _ pounds of any one class.
Ans: 100 pounds

Q. Which of these statements about seeing ahead is true?
Ans: Good drivers should keep attention back and forth, rear and far

Q. The maximum distance you should stop from a railroad
crossing is:
Ans: 50 feet

Q. It is most dangerous to back up:
Ans: To the right.

Q. You are driving on a slippery road during the day. How much space does the Driver’s manual say you should keep ahead of you?
Ans: Allow much more space than needed for ideal driving conditions.

Q. Which of these statements about managing space to the sides of your bus is true?
Ans: You should avoid traveling next to others when possible.

Q. Your bus is disabled. The bus, with riders aboard, may be towed or pushed to a safe spot to discharge passengers only if:
Ans: Getting off the bus sooner would be unsafe

Q. Which of these statements about seeing ahead is true?
Ans: Many drivers do not look far enough ahead.

Q. Normally, how many seats that are not securely fastened to the bus are allowed?
Ans: 0

Q. Shifting gears in a bus is not permitted when:
Ans: Crossing railroad tracks.

Q. Hazardous conditions are identified as:
Ans: Any condition that may cause your trip to be unsafe

Q. The bus driver should never change the location of a bus stop without approval from whom?
Ans: The appropriate district official.

Q. Buses are greatly affected by winds:
Ans: When coming out of tunnels

Q. Inspection of the vehicles by the driver is mandated by:
Ans: Federal and state laws.

Q. If a vehicle moves suddenly into your lane you should:
Ans: Slow down and pull to the right as far as you safely can. Sound your horn and flash your lights.

Q. Flat mirrors are mounted:
Ans: At the left and right front corners on the bus at the side or front of the windshield

Q. The (OIRM) is the inside rear-view mirror used to:
Ans: Monitor passenger activity inside the bus

Q. There is a blind spot directly behind the driver’s seat.
Ans: True.

Q. How many seats may be placed in the aisle if the bus is a charter and is carrying agricultural (farm) workers?
Ans: 8

Q. When is it recommended that you wear a seat belt?
Ans: Always

Q. The standee line is
Ans: A two-inch line at the front of the bus indicating that no passenger may stand in front of it

Q. Recapped tires are permitted on the steering axle provided
Ans: Never

Q. All of the following are required during your pre-trip inspection, except
Ans: Check cylinder wall thickness

Q. When stopping at a railroad crossing, you must stop
Ans: No closer than 15 feet, no farther than 50 feet

Q. Which of the following is true about refueling your bus?
Ans: Never refuel with passengers aboard when in a closed building

Q. Which of the following hazardous materials are you permitted to transport?
Ans: Small arms ammunition (ORM-D)

Q. You are approaching a drawbridge and no signal device or attendant is present, you must
Ans: Stop at least 50 feet before the draw of the bridge

Q. If you must discharge an unruly or disruptive passenger, you should
Ans: Choose a location that is safe and well lighted

Q. Passengers may carry gasoline onto the bus
Ans: Never

Q. Which of the following emergency equipment is required on your bus?
Ans: Fire extinguisher, 3 reflective triangles, spare electric fuses, unless bus is equipped with circuit breakers

Q. Speed limits on curves are standardized for
Ans: Automobiles

Q. If your bus is not carrying farm workers, how many aisle seats are you permitted?
Ans: 0

Q. Which of the following hazardous materials are you permitted to transport?
Ans: Emergency shipment of drugs, emergency shipment of hospital supplies, small arms ammunition (ORM-D)

Q. You are driving at night and you must dim your headlights from high to low. What should you do with your speed?
Ans: Slow down

Q. Which of these should be considered a hazard?
Ans: An ice-cream truck, a blind intersection, and a driver signaling a turn

Q. You are driving a 40-foot bus at 45 mph. The road is dry and visibility is good. You should keep a safety space in front of your bus that is at least
Ans: 5 seconds

Q. When should you check your mirrors for a lane change?
Ans: Before and after signaling the change, right after starting the lane change, and after completing the lane change

Q. Which of these will result in the best control on curves?
Ans: Slow to a safe speed before entering curves, then accelerate slightly through the curves

Q. Your bus is disabled. The bus, with riders aboard, may be towed or pushed to a safe spot to discharge passengers only
Ans: If getting off the bus would be more risky for the riders

Q. When inspecting your bus, you must make sure that
Ans: Every handhold and railing is secure, river signaling devices are working and emergency exit handles are secure

Q. When is it best to wear your seat belt?
Ans: Always

Q. Which of these statements about speed management and braking is true?
Ans: You need about four times as much stopping distance at 40 mph as at 20 mph

Q. With passengers onboard, you must never fuel your bus
Ans: In a closed building

Q. When stopping for railroad tracks, you must stop no closer than how many feet before the nearest track.
Ans: 15

Q. You may sometimes haul small arms ammunition, emergency shipments of drugs, or hospital supplies on a bus. The total weight of all such hazardous materials must not be greater than
Ans: 500 pounds

Q. How many folding aisle seats are allowed in a bus that is not carrying farm workers?
Ans: 0

Q. If there is no traffic light or attendant, how far from the draw of a drawbridge must you stop?
Ans: 50 feet

Q. A bus may carry baggage or freight in the passenger area only if it is secured and meets which of the following requirements?
Ans: The driver can move freely and easily, any rider can use all exits, and riders are protected from falling or shifting packages

Q. If your bus is equipped with an emergency exit door, it must
Ans: Be secured when the bus is being driven

Q. Which one of the following types of cargo must never be carried on a bus with passengers?
Ans: Tear gas

Q. When you discharge an unruly passenger, you should pick a place that is:
Ans: As safe as possible, or the next stop

Q. The reason you must be alert for road hazards is so
Ans: You will have time to plan your escape if the hazard becomes an emergency

Q. If your bus has an emergency exit door, it must:
Ans: Be closed when operating the bus.

Q. Many buses have curved (convex or “spot”) mirrors. These mirrors:
Ans: Make things seem smaller and farther away than they really are.

Q. To stop for railroad tracks, a bus driver must stop how many feet before the nearest track?
Ans: 15 to 20

Q. When you inspect your bus, make sure that:
Ans: Rider signaling devices are working.

Q. If a rider wants to bring a car battery or a can of gasoline aboard your bus you should:
Ans: Not allow the rider to do it.

Q. If there is no traffic light or attendant, stop for a drawbridge about how many feet from the draw?
Ans: 50

Q. You should not let riders stand:
Ans: In front of the standee line.

Q. You are driving a 40-foot bus at 50 mph. The road is dry and visibility is good. You should keep at least how many seconds pace in front of your bus to be safe?
Ans: 5

Q. You are driving a 40-foot bus at 30 mph. The road is dry and visibility is good. You should keep a safe space in front of your bus that is at least how many seconds?
Ans: 4

Q. It is best to wear your seatbelt:
Ans: At all times.

Q. Buses may have recapped or regrooved tires:
Ans: Anywhere except the front wheels.

Q. Which of the following lists the three types of emergency equipment that you must have on your bus?
Ans:
– Fire Extinguisher
– Spare Electrical Fuses (unless equipped w/ circuit breakers)
– Reflectors

Q. You may sometimes haul small-arms ammunition or emergency hospital supplies on a bus. The total weight of all such hazardous materials must not be more than how many pounds?
Ans: 500

Q. Which of the following types of cargo can never be carried on a bus?
Ans: Irritating materials or tear gas.

Q. If you have riders aboard, you should never fuel your bus:
Ans: In a closed building.

Q. A bus may carry baggage and freight only if secured so:
Ans: Any rider can use any door or window in an emergency and riders are protected from falling or shifting packages.

Q. When you discharge any unruly rider, you should chose a place that is:
Ans: As safe as possible.

Q. Which of these will result in the best control on curves?
Ans: Slow to a safe speed before entering curves, then accelerate slightly through them.

Q. How many folding aisle seats are allowed in a bus that is not carrying farm workers?
Ans: 0

Q. Normally, how many seats that are not securely fastened to the bus are allowed?
Ans: 0

Q. Which of these statements about speed management and braking is true?
Ans: You need about four times as much stopping distance at 40 mph as at 20 mph.

Q. Which of these statements about managing space to the side of your bus is true?
Ans: You should avoid traveling next to others when possible.

Q. Which of these statements about seeing ahead is true?
Ans: Many drivers do not look far enough ahead.

Q. You are driving at night and you must dim your headlights from high to low. What should you do with your speed?
Ans: Slow down.

Q. Which would most effect the amount of traction that your bus will have?
Ans: The type and condition of the road surface.

Q. Shifting gears in a passenger transport vehicle is not permitted when:
Ans: Crossing railroad tracks.

Q. It is most dangerous to back up:
Ans: To the right.

Q. When backing, a bus will have the most traction when:
Ans: The wheels are rolling, just short of locking

Q. When you are driving too fast on a banked curve, your bus will:
Ans: Lean toward the outside.

Q. If defects that were reported earlier have been fixed, how do up certify this on your pre-trip inspection
Ans: By signing the previous driver’s endorsement

Q. During this inspection, what are some items that you must check
Ans: The service brakes, steering lights, vision mirrors, wheels, and rims

Q. On which wheels may buses have recapped or regrouped tires
Ans: On all wheels except the front wheels

Q. Which of these is the best to do when testing for hydraulic leaks
Ans: 3 pumps on the brakes for 5 seconds

Q. What are three types of emergency equipment you must have on a bus
Ans: Reflectors, a fire extinguisher, and unless your bus has circulated circuit breakers, spare electric fuses

Q. Before driving a passenger vehicle, the emergency equipment must be in place and ready to use. Who must make the inspection to verify this
Ans: The driver

Q. A CDL holder operating a CMV found to have any alcohol in his or her system is placed out of service for at least how many hours
Ans: Twenty-four hours may passengers

Q. May passengers leave carry-on baggage in a doorway or in the aisle
Ans: There should be nothing in a doorway or in the aisle that might h t trip riders

Q. The rules require shippers to mark containers of hazardous material with certain labels. What shapes are these labels
Ans: Diamond-shaped

Q. What is the maximum weight of acceptable hazardous materials that may be carried by a passenger transport vehicle
Ans: Five hundred pounds

Q. What is the total weight of hazardous materials of one class that may be carried
Ans: One hundred pounds

Q. Can oxygen be carried on board by a passenger
Ans: Yes, if medically prescribed for and in the possession of a passenger

Q. While certain emergency hospital supplies may be transported on a passenger bus, can tear gas be so transported
Ans: No, irritating material may be carried

Q. Which of these two items can be carried on a bus by a rider
Ans: Neither one (gasoline nor car batteries)

Q. Where must passengers who are standing remain while the bus is underway
Ans: On buses where standing is permitted they must stand behind the standee line

Q. Can the emergency exit door be opened when the bus is operating
Ans: The emergency exit door must be secured

Q. If you should have to discharge an unruly passenger, where should this be done
Ans: At a place that is safe for them

Q. While driving, you look at the road ahead, to the rear. Where else should you look
Ans: Also scan the interior of the bus

Q. While some bus accidents happen at intersections, buses can have an accident with cars going in the same lane. Why will looking ahead of your bus help prevent such an accident
Ans: You can see changes in the flow early enough to make needed adjustments

Q. If you should have to move quickly to avoid an accident, it is important to know what
Ans: Where other vehicles are around your bus

Q. Of course three hazards which can cause the most (only) dangerous driving conditions in poor weather
Ans: Ice

Q. What is a factor that most affects the amount of traction that your bus has
Ans: The type and condition of the road surface

Q. In backing up, it is least dangerous to back straight back. Which is more dangerous
Ans: Backing to the right

Q. Time-wise, if you are driving a vehicle that is forty feet long, how far should you follow other vehicles to be safe if your speed is 35 mph
Ans: At least four seconds

Q. A bus loses traction when the wheels are locked. When braking, when will a bus have the most traction
Ans: When the wheels are rolling, just short of locking up

Q. When driving down a steep hill which is best
Ans: It is best to have shifted down to a lower gear so that you will not use your brakes hard

Q. If the posted speed on a curve is 45 mph, what is a safe speed for your bus
Ans: It may be exactly 45 miles per hour or it could be less

Q. Which may will your bus lean if you are driving too fast on banked curve
Ans: It will lean toward the outside

Q. What should you do about the speed of your vehicle if the road become slippery
Ans: Reduce your speed gradually

Q. When chains are required to be installed, they should be installed on which wheels
Ans: The drive wheels

Q. When may a disabled bus be towed or pushed to a safe place with passengers still on board
Ans: Only if getting off would be unsafe for the passengers

Q. Are you allowed to shift gears when crossing railroad tracks
Ans: No

Q. How many feet away from the nearest track must you stop you bus when stopping for railroad tracks
Ans: At least 15 feet, but not more 50 feet from the crossing

Q. You are stopped for railroad crossing. When may you open your doors
Ans: You should open your forward door if it improves your ability to see or hear an approaching train

Q. There is no traffic light or attendant on duty and you have stopped for a drawbridge. How far must you stop from the draw of the bridge.
Ans: At least 50 feet

Q. Name a situation where you must not allow your bus to be fueled
Ans: When in a closed building or with riders on board

Q. While you do not have to stop, you must slow down and carefully check for other vehicles when
Ans: All of the above (at a streetcar crossing, at railroad tracks used only for industrial switching within a business district, at a crossing marked “except crossing”).

Q. Which of these is best to do when testing service brake stopping action
Ans: All of the above (Go about 4 mph, & Push brake pedal softly)

Q. Urban mass transit coaches may have a brake and accelerator interlock system. What is the function of the interlock
Ans: It applies the brakes and holds the throttle in an idle position when the rear door is open

Q. As part of the standard emergency equipment, buses must always carry fire extinguishers, spare electrical fuses unless equipped with circuit breakers, and
Ans: Reflectors

Q. Buses may carry which of the following
Ans: Small arms ammunition labeled ORM-D

Q. Buses should stop at least __ feet before a drawbridge
Ans: 50

Q. Which of the following is considered a hazard
Ans: All of the above (a rental truck, a stopped bus, a bicyclist)

Q. When arriving at the destination or intermediate stops the driver should announce
Ans: All the above (the location, the reason for stopping, the next departure time and bus number)

Q. The front wheels of the bus may never
Ans: A and B (have recapped tires, have regrooved tires)

Q. Buses must always stop 15 to 50 feet before a railroad crossing and
Ans: Listen and look in both directions for trains

Q. Whenever you double your speed, it takes about __ times as much distance to stop
Ans: 4

Q. Drivers should always slow their speed before entering a curve. If you take a curve too fast, your vehicle might turn over or
Ans: Lose traction and continue straight ahead

Q. You should always __
Ans: Allow more space when driving on a slippery road than in ideal driving conditions

Q. Bus drivers should __
Ans: All of the above (never refuel in a closed building with riders on board, not tow or push a disabled bus with riders aboard either vehicle unless getting off would be unsafe

Q. Buses designed to allow standing must have a two-inch line on the floor or some other means of showing riders where they can stand. This line is a __
Ans: Standee line

Q. Which of the following statements it’s true
Ans: All of the above (you should decrease your speed when dimming your headlights from high to low, fog may require you to slow down, rain may require you to slow down

Q. You are driving a 30-foot vehicle at 38 mph on dry road with good visibility. You should keep a safety space in front of your bus that is at least
Ans: 3 seconds

Q. It is very important that bus drivers always
Ans: Wear seat belts

Q. You are driving a bus. You:
Ans: Should NEVER talk unnecessarily with riders.

Q. Which of these actions will result in the best control on a curve?
Ans: Slow to a safe speed before entering a curve, then accelerate slightly through it.

Q. A bus with riders aboard becomes disabled. The bus may be towed or pushed to a safe place to discharge the passengers only:
Ans: Getting off the bus sooner would be unsafe.

Q. When you arrive at a bust stop, you should announce the reason for stopping and the:
Ans: Location, departure time, and the bus number

Q. You are approaching railroad tracks. A bus driver must stop _ to _ feet before the nearest track.
Ans: 15;50

Q. You must sign the previous driver’s inspection report only when:
Ans: The defects reported have been repaired

Q. If you work for an interstate carrier, you must complete an after-trip inspection report for each bus listing:
Ans: Any defects that would affect safety or result in a break down.

Q. A bus may carry baggage and freight only if it is:
Ans: Secured and out of the way of any exit

Q. Carrying hazardous materials on a bus is:
Ans: Permitted if the materials container is placarded

Q. Buses are allowed to carry less than 100 pounds of__ in the passenger area.
Ans: Small arms ammunition (ORM-D)

Q. You are driving at night and you must dim your headlights from high to low. What should you do with your speed?
Ans: Slow down

Q. Which statement is TRUE about seeing ahead?
Ans: Good drivers shift their attention back and forth, near and far.

Q. When driving a bus across railroad tracks, you:
Ans: Should NEVER change gears if your bus has a manual transmission.

Q. You are driving a 30-foot bus on a highway at 45 mph. The road is dry and visibility is good. A safe distance between you and the vehicle of you should be at least:
Ans: 4 seconds

Q. You should check your mirrors:
Ans: Regularly as part of your scan for potential hazards

Q. Many buses have curved (convex or “Spot”) mirrors. These mirrors:
Ans: Make things seem smaller and farther away than they really are.

Q. If there is no traffic light or attendant, stop for a drawbridge about __ feet from the draw
Ans: 50

Q. Buses may have recapped or re-grooved tires:
Ans: Anywhere except the front wheels

Q. When are you allowed to drive with an emergency exit door open?
Ans: You may NEVER drive with an emergency exit door open.

Q. You should not let riders stand:
Ans: In front of the standee line

Q. When you inspect your bus, make sure that:
Ans: Rider signaling devices are working

Q. You are driving on a slippery road during the day. How much space does the Commercial Handbook say you should keep ahead of you?
Ans: Allow “much more space” than needed for ideal driving conditions

Q. The maximum distance you can stop away from a railroad crossing is:
Ans: 50 feet

Q. If your bus leans towards the outside in a banked curve, You:
Ans: Are driving too fast

Q. Which of the following types of emergency equipment must you have on your bus?
Ans: Fire extinguisher, spare electric fuses, reflectors

Q. Which statement is TRUE about speed management and braking?
Ans: You need about 4 times as much stopping distance at 40 mph as you need at 20 mph.

Q. Buses must NOT carry more than __ pounds of any one class of allowed hazardous materials
Ans: 100

Q. While driving a bus, you should:
Ans: Scan the road ahead, as well as the interior of your bus.

Q. When driving a bus you should look __ seconds ahead of you.
Ans: 12 to 15

Q. The posted speed for a turn:
Ans: May be unsafe for a bus.

Q. When driving a bus, the emergency roof hatches:
Ans: May be locked in a partially open position for fresh air.

Q. Which of the following types of cargo can NEVER be carried on a bus?
Ans: Irritating materials or tear gas

Q. A bus must stop at least__ feet before the draw of a drawbridge that does not have a signal light or an attendant:
Ans: 5o

Q. You are driving a 40-foot bus at 50 mph. The road is dry and visibility is good. You should keep at least__ seconds of space in front of your bus to be safe.
Ans: 5

Q. If a bus breaks down and there are passengers on board, the bus:
Ans: Should not be towed until the passengers are discharged.

Q. The total maximum weight of hazardous materials that buses are allowed to carry is __ pounds.
Ans: 500

Q. Buses may have re-capped or re-grooved tires:
Ans: Anywhere except the front wheels

Q. When you discharge an unruly rider, you should choose a place:
Ans: That is as safe as possible

Q. When you are driving, a hazard is:
Ans: Anyone or anything that may cause an unsafe condition.

Q. If you have riders on the bus, you should never fuel your bus:
Ans: In a closed building

Q. Baggage or freight carried on a bus must be secured:
Ans: So any door or window can be used in an emergency.

Q. A standee line on a bus:
Ans: Is the line that all riders must stay behind while the bus is moving

Q. Which actions will result in the best control on a curve?
Ans: Slow to a safe speed before entering a curve, then accelerate slightly though it.

Q. When waiting to merge into traffic, you should:
Ans: Always wait for a large enough gap before merging.

Q. Which statement is true about managing space to the sides of your bus?
Ans: You should avoid traveling next to others when possible.

Q. Drivers of charter buses should NOT allow riders on the bus until:
Ans: Departure time

Q. Your bus is disabled. The bus, with riders on board, may be towed or pushed to a safe spot to discharge the passengers only if:
Ans: Getting off the bus sooner would be unsafe.

Q. How many folding seats are allowed in a bus that is NOT carrying farm workers?
Ans: 0

Q. If your bus has an emergency exit door, it must:
Ans: Be closed when operating the bus

Q. You may sometimes transport small arms ammunition or emergency hospital supplies on a bus. The total weight of these hazardous materials must not exceed __ pounds.
Ans: 500

Q. You are driving a 40-foot bus at 30 mph. The road is dry and visibility is good. You should keep a safety space in front of your bus that is at least
Ans: 4

Q. A hazard is defined as:
Ans: Any condition which may cause your trip to be unsafe.

Q. If a rider wants to get on a bus with a car batter or a can of gasoline you should:
Ans: NOT allow the rider to get on

Q. Carry-on baggage:
Ans: Can NEVER be left in a doorway or an aisle.

Q. What is the term for driving more than 100 miles
Ans: Air miles

 

California CDL Test Questions and Answers – Combination Vehicles

Below you can find questions and their respective answers for the topic “Combination Vehicles”:

 

About California CDL Test

The California commercial driving license test is required for anyone who wants to operate a commercial vehicle in the state of California. The test is designed to ensure that drivers are familiar with the laws and regulations governing commercial vehicles and that they have the skills and knowledge necessary to safely operate these vehicles.

If you are interested in obtaining a California commercial driving license, you will need to pass the California commercial driving license test. This test is administered by the California Department of Motor Vehicles (DMV), and it consists of two parts: a written exam and a skills test.

Find more information here: DMV.CA.GOV

To prepare for the written exam, you should study the California Commercial Driver Handbook, which is available from the DMV website or your local DMV office. This handbook contains information on the laws and regulations governing commercial vehicles, as well as sample test questions.

The skills test is administered by a certified examiner, and it consists of two parts: a pre-trip inspection and a road test. During the pre-trip inspection, you will be asked to identify various parts of the commercial vehicle, and you will be asked to demonstrate your knowledge of the vehicle’s controls. During the road test, you will be asked to drive the commercial vehicle in various traffic situations.

You must pass both the written exam and the skills test in order to obtain a California commercial driving license. Once you have passed these tests, you will be issued a license that is valid for four years. After four years, you will need to renew your license by taking and passing the written exam and skills test again.

 

Thank for visiting @CaliforniaTomorrow 

 

Hope you got access to California CDL test questions and answers by following to above what we shared. Share with other students if you find it helpful.

Leave a Comment